|
3 Replies and 3502 Views
movement freezes
3502 3 - Started by newillumination, last post from newillumination
Im running capture along with avolites D4 simulator on the same computer, via an ACDI from avolites. Recently Ive found that any movement with a time fade will freeze halfway throug the move, as if the DMX stream stops. When I send new DMX info, for example a new colour or gobo, the move will continue. This also happens with movement chases and shapes. Funny thing is, when I use my skype phone on same computer, then it all works fine. Its almost as if some connectuion or port on the PC closes an...
|
|
|
3 Replies and 4075 Views
ATI or NVidia
4075 3 - Started by tomvision, last post from newillumination
I'm looking for a new graphic card and I don't know if it's better to take an ATI or a NVidia chip'...
I also think that 1 Gb is better than 512...
I tried Capture with a Nvidia 9400 chip and 512Mb memory, it runs, but sometimes it freezes (only full-screen)
Thanks
|
|
|
1 Replies and 2715 Views
Fixtures Library
2715 1 - Started by Deleted User, last post from Vangelis Manolis
Hello everyone,
Where do I send mail to include new reference in the Library of Capture Console
What do I provide for this
Thank you for your responses.
|
|
|
1 Replies and 3163 Views
sequential Unit numbering Mac OS X and Capture 2.2.6
3163 1 - Started by Florian Baeumler, last post from Lars Wernlund
Hi,
I have a problem with the unit numbering 'wizard'. Once I started numbering units I can't reset the unit number. I press reset and in the window it does reset, but when I continue numbering it does continue from the last set unit number. I also tried typing in the new number and pressing return to no effect.
Anyone any ideas
Kind regards
Florian
|
|
|
2 Replies and 3191 Views
Plots
3191 2 - Started by stagedude, last post from Lars Wernlund
I was wondering if there is a way to rotate the top view in the plot to help fit it in the page better. Also I noticed that the top view has symbols but they are all pointing the same direction as opposed to pointing where they are focused in Polar. Is there any way to get the symbols on the plot to match where they are focussed in Polar
|
|
|
3 Replies and 3875 Views
dimmers are ON after instal new library file
3875 3 - Started by koenv, last post from Lars Wernlund
Hi capture Team,
i have install the new library file.now in my project the lamps are ON also when the dimmer 0
It occurs with the sun strip but also with a 4 lamp and stage blinder (audience blinder)
Also within A new project the same problem occurs
RegardsKoenV
|
|
|
|
1 Replies and 2786 Views
laptop
2786 1 - Started by newillumination, last post from tomvision
I'm about to buy a new laptop and wanted to know what anyone else is running and especially what not to buy. I'm running an ATI crad at the moment and cannot run capture polar graphics. I also find visualisation runs very slow when I hook it up to a desk and try to run more than 2 universes. Any tips recommendation would be appreciated
Thanks Yenz
Newillumination lighting design
|
|
|
2 Replies and 3210 Views
Can't change Slot Frames
3210 2 - Started by stagedude, last post from stagedude
Hello I'm using Capture Polar on a Mac running Snow Leopard. When I put a color filter or a gobo in the slot frame of a fixture I can't seem to change or delete it later. I've gone into the fixture tab and also the properties of the selected object. Each time I highlight the slot frames for either section I try to delete or move the filter or gobo and nothing happens. If I just try putting a different filter or gobo in its place it just adds the two together.
|
|
|
1 Replies and 2994 Views
Sketchup and Capture Polar
2994 1 - Started by stagedude, last post from Lars Wernlund
I was looking through the forums and saw that two years ago you were working on getting sketchup to work with Caputure. Has any progress been made on that
|
|