|
1 Replies and 654 Views
Snap to pipe and move with dmx mover
654 1 - Started by Georg Vogt, last post from Georg Vogt
Hi there and thanks for any help,
I have built a 3D model of our theatre and want to adapt it according to the needs of the performances. All should be done with dmx movers and rotators. Flats, curtains, cycs etc went fine but now the fixtures on a pipe should be moved together with that pipe through the dmx mover of that pipe. Does anyone have a solution Thanks again.
|
|
|
1 Replies and 552 Views
Universes in demo version
552 1 - Started by Prodco, last post from Prodco
Hi there
Im really enjoying my demo version of Capture. However, I cant seem to have fixtures on universe B respond to DMX. Ive successfully exported all of my fixtures out of Vectorworks and have mapped the "Universe/Address" field in VW to "Patch" in Capture at the import. All fixtures on Universe A are receiving DMX via sacn. Im running Onyx on the same PC.
Is the demo version limited to 1 universe
Cheers
|
|
|
5 Replies and 1043 Views
Export from vectorworks
1043 5 - Started by Prodco, last post from Aira Euro
Hi there
Im assessing a demo to see how I can incorporate capture into my workflow. I do all my design work in VW - but havent managed to successfully import lighting fixtures, apart from their geometric shapes as a DWG file. The fixtures show in the Fixtures window, but not in any of the Capture views. I successfully import a DWG from VW and I can see all the geomtery. I export fixtures via the "Export Instrument Data" command in VW. I then try to import this via the &quo...
|
|
|
1 Replies and 537 Views
student edition 2018 or nexum
537 1 - Started by allofull, last post from allofull
I need an old capture relise to install on my 2011 imac.
I&39;m looking for the 2018 or nexum in student version
I&39;ve already asked the support team but they don&39;t have the installs to send me.
there is someone in the forum who has installed them and wants to share them with me
tks!
|
|
|
2 Replies and 689 Views
Truss motion by 2 dmx movers?
689 2 - Started by Subbass, last post from Subbass
Hi Guis,
Is it possible to connect left side of the truss to dmx mover1, and the right side to dmx mover 2, and to change the angle of that truss, not only highness
Best Regards!
|
|
|
|
|
3 Replies and 781 Views
Spotlight focus range problem
781 3 - Started by Nikita, last post from Vasilis Ziogas
Hello!
I am creating a model of a theater stage. This scene has Licht-Technik Selecon Rama PC (pan / tilt / motor zoom). I need to sync all parameters. There is a problem with the zoom: Capture is showing incorrect zoom. The spotlight has 5-60 degrees, but in fact I see 30-45 degrees. What am I doing wrong Is it possible to calibrate the zoom range Capture 2020 Solo ETC EOS 3.0 MacOs
Thanks!
|
|
|
2 Replies and 710 Views
focus plane: heatmap mode
710 2 - Started by Ondrej Ruzicka, last post from Ondrej Ruzicka
Hello
I found really interesting the focus plane feature and especially the heatmap mode. I would like to ask whether is it only a really cool way of showing the evenness of a wash light or if it could be used to get some rough real world values.
So: How accurate it is I assume it calculates values from direct lighting (no reflections etc.) And since the light outputs are modeled by photometric data from manufacturers, it should yield some accuracy...
|
|
|
|
|
3 Replies and 811 Views
Student version setup
811 3 - Started by Norm, last post from Vasilis Ziogas
Our local theater just upgraded its light board and lights to a colorsource 40 light board and ETC led (6ch, sorry can&39;t remember model right now) lights.
I have downloaded both Capture 2020 student v2020.0.48 and colorsource v31.1.0.23
I can&39;t seem to connect these programs so I can control the lighting setup in capture with the virtual colorsource light board. How do I link them so they work together.
Our theater uses ETC LED (6ch/no PTZ) lights which a...
|
|